BETENBENDER 6' x 120 Ton Hydraulic Press Brake Model 6-120

BETENBENDER 6' x 120 Ton Hydraulic Press Brake Model 6-120

$54,200

orCall 386-304-3720

Description

Please note: many products ship straight from manufacturer

** FREE SHIPPING TO COMMERCIAL ADDRESS THAT CAN OFFLOAD**

***SHIPPING IS TO LOWER 48 STATES ONLY. OTHER AREAS PLEASE EMAIL

BETENBENDER 6' x 120 Ton Hydraulic Press Brake Model 6-120

  • ACCURACY
  • Every Betenbender machine is thoroughly inspected and tested.
  • 1.Parallelism is maintained between bed and ram or at preset angle by using precision automatic leveling controls. Parallelism is maintained at +/-.002" in low speed.
  • 2.The ram bottom reversal point is controlled by precise limit switches referenced off the bed. This isolates housing deflections, which can interfere with its accuracy.
  • ENHANCED PRODUCTIVITY
  • Return speed and rapid advance facilitates high cycle rates. Operator control is simplified by slow and press speed, thus work
  • spoilage is avoided. Rapid advance with automatic change. The point of speed change is fully adjustable by electric limit switch.
  • Micrometer type tilt adjustment is graduated in .001" increments permitting ram tilt adjustments up to 1/2" in either direction.
  • ELECTRO MECHANICAL STROKE CONTROL is bed referenced.
  • Bottom limit is manually set with a lead screw and displayed by an mechanical readout calibrated in .001" increments.
  • VERSATILITY
  • BETENBENDER'S press brakes have long full tonnage strokes, adjustable length and selectable speed combinations, adjustable height for short stroke, 2-speed standard and the optional 3- speed for adjustable low speed to prevent whip
  • ELECRICAL EQUIPMENT
  • Meets requirements of NFPA no.79, JIC and construction requirements of the latest ANSI B-11.3 Standards. Includes drip-proof, continuous duty 45 degree Celsius ambient hydraulic pump motor wired for 230 or 460 volt, 3 phase 60 hertz.
  • DEPENDABILITY
  • Self-lubricating replaceable non-metallic ways prevent galling and provide long service life. Cylinders are high-strength, all steel. To minimize wear and provide a superior oil seal, inside cylinder surfaces are honed to a mirror finish.
  • Compact, precision machined aluminum manifold incorporates off-the shelf components, minimizes piping and consolidates "O" ring mounted valves.
  • Quiet, vane type, constant volume pumps. In keeping with good hydraulic design practice, these energy efficient pumps are located outside the reservoir.
  • Filtration of contaminants as small as 10 microns is accomplished with intake and discharge filters. A built-in magnetic trap and air breather filter provides added protection against contaminants. Reservoir of large capacity facilitates effective heat dissipation. A fluid level gauge is provided.
  • CONTROL
  • Main Control Cabinet - NEMA 12 enclosures mounted in the right housing containing: magnetic non-reversing motor starter and 120 volt circuit.
  • Main motor START button and STOP button are illuminated.
  • RAM UP and RAM DOWN buttons.
  • RUN/JOG Switch.
  • Fusible disconnect.
  • MAINTENANCE
  • Clevis mounted cylinders eliminate cylinder binding by reducing the possibility of oil leaks from cylinder binding.
  • (Pins & bushings do not rotate under load, this reduces excessive wear)
  • MADE IN USA



STANDARD EQUIPMENT:

  • Clamp Type Back-gauge-Manual Adjustable X,Y,Z
  • NEMA Electrics
  • All Hydraulic Fluid Included
  • American Made Motor
  • Three Speed (95T and Larger)
  • Hour Meter
  • Lifetime Telephone Support @ No Charge
  • Bottom Time Delay
  • Three Position Foot Pedal
  • Depth Stop w/Digital Readout
  • All Steel Construction
  • Disconnect Switch
  • Two-Speed Ram
  • All Components Available from Local Suppliers 


OPTIONAL ITEMS: CALL FOR PRICE

  • *Manual Front Reading Backgauge (24") w/Mechanical Readout
  • Power Front Reading Backgauge w/5 Station NC "Go To" Controller on Pendant
  • Power Ram Adjustment w/5 Station NC "Go To" Controller on Pendant
  • Extra Length on Backgauge
  • Micrometer Precision Gauge Unit (2 Required)
  • CNC Ram Stop
  • CNC Backgauge
  • *24" Support Arms "Slide" Type
  • Extend Support Arms (each)
  • Disappearing Stops
  • *Work Light
  • *Variable Tonnage Control
  • *One Shot Lubrication
  • Automatic Lubrication
  • Oil Cooler
  • *Light Curtain w/Full Fence
  • *Operator Station Palm Control
  • Additional Foot Pedal w/Key Lock
  • Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height.)
  • Dove Tails or T‑Slots
  • Ram Machining
  • Bed Machining Angle Brackets
  • Angle Brackets (Plates) for Top (4"x4") 18" Shorter than Bed
  • Angle Brackets (Plates) for Bottom (4"x4") 18" Shorter than Bed
  • Increase Throat Gap or Increase Open Height
  •  Increase Stroke Length
  • Keylock Switch
  • Die Rollover Bars (Recommended for 4/Way Dies)
  • Air Lift (Recommended for 4/Way Dies)
  • Dual Calibration
  • 208V
  • Crating Charge (Not An Export Crate) Still Requires Tarping
  • Special Paint Colors
  • Bolt/Shim Kit for Leveling
  • Ram Stop Control (1/4" Above Die)
  • Rigging, Lagging, Leveling & Electrical Hook Up is Customers Responsibility
  • NOTE: DIE RISERS NOT FURNISHED
  • ASK ABOUT OPTIONS NOT LISTED.
  • ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
  • *RECOMMENDED OPTIONS


Specifications

ManufacturerBetenbender
Model6-120
ConditionNew
Stock Number6-120
Maximum Tonnage120 Tons
Maximum Bending Length72"
Maximum Stroke Length8"
Closed Height6"
Open Height14"
Throat Depth8"
Distance Between Housings54-1/2"
Ram Repeatability+/- .002"
Hydraulic Pressure2,500 lbs.
Hydraulic Oil Capacity65 gallons
Machine Weight17,000 lbs.
Machine Dimensions: Overall Height103"
Machine Dimensions: Overall Length100"
Machine Dimensions: Overall Width56.5"
Motor Horsepower20